Fasteners
Industrial Fasteners for Construction, Fabrication & Maintenance
Industrial fasteners are the backbone of mechanical fastening, anchoring, and structural assembly across a wide range of industries. Our comprehensive selection is engineered to meet the rigorous demands of industrial, fleet, and maintenance, repair, and operations (MRO) applications. Whether you require metric or standard sizes, our fasteners ensure compatibility and consistent sizing for seamless repair, replacement, and new installations. From heavy-duty construction projects to precision fabrication and ongoing equipment service, our hardware solutions support every phase of your operation. Explore a broad inventory designed for structural integrity, mechanical reliability, and secure anchoring—empowering your team to work efficiently and safely, no matter the jobsite or application.
Bolts, Screws & Threaded Rod
Discover our extensive range of bolts, screws, and threaded rod, available in both standard and metric dimensions. These essential fasteners provide reliable mechanical connections for structural assembly, equipment installation, and repair. For more details, visit our Bolts, Screws & Threaded Rod category.
Nuts, Washers & Locking Hardware
Ensure secure fastening and load distribution with our selection of nuts, washers, and locking hardware. Designed for compatibility with a variety of bolts and threaded rods, these components are critical for maintaining joint integrity in demanding environments. Explore the full range in our Nuts, Washers & Locking Hardware section.
Anchors & Threaded Inserts
Achieve dependable anchoring in concrete, masonry, and other substrates with our anchors and threaded inserts. These solutions are ideal for structural and mechanical applications where secure, long-lasting fastening is required. Learn more in our Anchors & Threaded Inserts category.
Pins, Retaining Rings & Rivets
For applications requiring precise alignment, retention, or permanent assembly, our pins, retaining rings, and rivets deliver consistent performance. These specialty fasteners are essential for equipment maintenance, fabrication, and assembly tasks. Visit our Pins, Retaining Rings & Rivets page for more information.
Specialty Fasteners & Hardware
Address unique fastening challenges with our specialty fasteners and hardware, including tamper-resistant, high-strength, and application-specific solutions. Support your fabrication, installation, and service needs with products engineered for reliability and ease of use. Browse our Specialty Fasteners & Hardware category for tailored options.
Value Propositions
- Broad selection of standard and metric fasteners for every application
- Suitable for industrial, fleet, and maintenance use
- Structural, mechanical, and anchoring solutions for diverse environments
- Consistent sizing for efficient repair and replacement
- Supports fabrication, installation, and equipment service
HEX CAP SCREW UNC STAINLESS 1/2"-13 X 2"
- Grade 18-8 stainless steel hex cap screws.
- Used in products that require general atmospheric corrosion resistance such as chemical and food processing equipment and marine applications.
- Tensile strength: 100,000 psi. minimum.
- Unified screw threads :UNC.
- Diameter: 1/2"-13.
- Length: 2".
$2.2838
CLEVIS PIN - ADJUSTABLE PLAIN 1/2" DIA. 3" LONG
- A quick replacement pin.
- Feature a series of holes making it adaptable to varying lengths.
- Easily replaces bolts, cotter pins or rivets on all types of equipment.
- Use the diameter that fits your application and cut off the excess length.
- Plain finish.
- Diameter: 1/2".
- Length: 3".
$3.2214
HEX CAP SCREW UNC 304 SS 1/2"-13 X 3"
- Grade 18-8 stainless steel hex cap screws.
- Used in products that require general atmospheric corrosion resistance such as chemical and food processing equipment and marine applications.
- Tensile strength: 100,000 psi. minimum.
- Unified screw threads :UNC.
- Diameter: 1/2"-13.
- Length: 3".
$1.5609
HEX CAP SCREW BOLT 1/2-13" X 12" GR 8 ZY
- Made from medium carbon alloy steel.
- Heat treated.
- Tensile strength: 150,000 psi. minimum.
- Yellow zinc plated.
- Unified screw threads :UNC.
- Diameter: 1/2"-13.
- Length: 1-1/2".
$1.4849
HEX CAP SCREW BOLT UNF ZINC 1/2"-20 X 1-1/2", GR 5
- Made from medium carbon steel.
- Heat treated.
- Tensile strength: 120,000 psi. minimum.
- Zinc plated.
- Unified screw threads :UNF.
- Diameter: 1/2"-20.
- Length: 1-1/2".
$1.1457
HEX CAP SCREW BOLT UNF ZINC 1/2"-20 X 1-1/2", GR 8
- Made from medium carbon alloy steel.
- Heat treated.
- Tensile strength: 150,000 psi. minimum.
- Yellow zinc plated.
- Unified screw threads :UNF.
- Diameter: 1/2"-20.
- Length: 1-1/2".
$1.6696
WOOD SCREW PHILLIPS FLAT HEAD #12 X 1-1/2"
- A thread forming screw having a gimlet point, and a sharp crested, coarse pitch thread.
- Will produce a mating thread when assembled into wood or other resilient materials.
- Flat head Phillips.
- Zinc plated steel.
- Diameter: 12
- Length: 1-1/2"
$0.3144
SHEET METAL SCREW HEX WASH HD #12 X 1-1/2"
- A thread forming tapping screw with spaced threads and a gimlet point.
- For self starting in thin metal or resin-filled plywood.
- Has an indented top surface, six flat sides with a flat washer which projects beyond the sides and provides a flat bearing surface.
- The washer and head are formed together as one piece. (Hex washer slotted head)
- Increased bearing area reduces likelihood of crushing mating surfaces.
- Zinc plated steel.
- Screw diameter 12
- Screw length 1-1/2 inches
$0.3216
SHEET METAL SCREW OVAL PHIL HD #12 X 1-1/2" STAINLESS
- A thread forming stainless tapping screw with spaced threads and a gimlet point.
- For self starting in thin metal or resin-filled plywood.
- A countersunk head with a rounded top surface and a cone-shaped bearing surface.
- Preferred over a flat head in conical applications, or when a more decorative finished look is desired.
- The countersunk surface nests into mating countersunk application sites.
- Oval head, phillips drive
- Screw diameter 12
- Screw length 1-1/2 inches
$0.3817
SHEET METAL SCREW PHIL PAN HD #12 X 1-1/2"
- A thread forming tapping screw with spaced threads and a gimlet point.
- For self starting in thin metal or resin-filled plywood.
- Phillips Pan Head
- For general applications.
- Can be substituted in most applications for round, truss or binding screws.
- Steel zinc plated.
- Diameter: 12
- Length: 1-1/2"
$0.3048
SHEET METAL SCREW PHIL PAN HD #12 X 1-1/2" STAINLESS
- A thread forming stainless tapping screw with spaced threads and a gimlet point.
- For self starting in thin metal or resin-filled plywood.
- Pan heads have a rounded top surface, cylindrical sides and a flat bearing surface.
- For general applications.
- Can be substituted in most applications for round, truss or binding screws.
- Pan head, phillips drive
- Screw diameter 12
- Screw length 1-1/2 inches
$0.696
TEK SCREW HEX WASHER HD #12 X 1-1/2"
- A tapping screw with spaced threads and a drill point which drills its own hole.
- May be used to attach plywood, soft woods or composition board to metal, or attach metal to metal.
- All self-drilling screws offer economical benefits: reduces labor and tooling costs; reduces or eliminates drill bits and taps.
- Hex washer head.
- Steel zinc plated.
- Rockwell hardness C52 minimum.
- Diameter: 12
- Length: 1-1/2"
$0.27
HEX CAP SCREW BOLT UNC ZINC 1/2"-13 X 1-1/4", GR 5
- Made from medium carbon steel.
- Heat treated.
- Tensile strength: 120,000 psi. minimum.
- Zinc plated.
- Unified screw threads :UNC.
- Diameter: 1/2"-13.
- Length: 1-1/4".
$0.6505
HEX CAP SCREW BOLT UNC ZY 1/2"-13 X 1-1/4", GR 8
- Assortments for UNC threads: C40AC8, C72AC8, C112AC8, GR8SVCKITA, GR8SVCKITB
- Heat treated.
- Tensile strength: 150,000 psi. minimum.
- Yellow zinc plated.
- Unified screw threads :UNC.
- Diameter: 1/2"-13.
- Length: 1-1/4".
$1.3148
HEX CAP SCREW BOLT UNF ZINC 1/2"-20 X 1-1/4", GR 5
- Made from medium carbon steel.
- Heat treated.
- Tensile strength: 120,000 psi. minimum.
- Zinc plated.
- Unified screw threads :UNF.
- Diameter: 1/2"-20.
- Length: 1-1/4".
$1.045
HEX CAP SCREW BOLT UNF ZINC 1/2"-20 X 1-1/4", GR 8
- Made from medium carbon alloy steel.
- Heat treated.
- Tensile strength: 150,000 psi. minimum.
- Yellow zinc plated.
- Unified screw threads :UNF.
- Diameter: 1/2"-20.
- Length: 1-1/4".
$1.4478
WOOD SCREW PHILLIPS FLAT HEAD #12 X 1-1/4"
- A thread forming screw having a gimlet point, and a sharp crested, coarse pitch thread.
- Will produce a mating thread when assembled into wood or other resilient materials.
- Flat head Phillips.
- Zinc plated steel.
- Diameter: 12
- Length: 1-1/4"
$0.294
SHEET METAL SCREW HEX WASH HD #12 X 1-1/4"
- A thread forming tapping screw with spaced threads and a gimlet point.
- For self starting in thin metal or resin-filled plywood.
- Has an indented top surface, six flat sides with a flat washer which projects beyond the sides and provides a flat bearing surface.
- The washer and head are formed together as one piece. (Hex washer slotted head)
- Increased bearing area reduces likelihood of crushing mating surfaces.
- Zinc plated steel.
- Screw diameter 12
- Screw length 1-1/4 inches
$0.252
SHEET METAL SCREW PHIL PAN HD #12 X 1-1/4"
- A thread forming tapping screw with spaced threads and a gimlet point.
- For self starting in thin metal or resin-filled plywood.
- Phillips Pan Head
- For general applications.
- Can be substituted in most applications for round, truss or binding screws.
- Steel zinc plated.
- Diameter: 12
- Length: 1-1/4"
$0.2472
SHEET METAL SCREW OVAL PHIL HD #12 X 1-1/4" STAINLESS
- A thread forming stainless tapping screw with spaced threads and a gimlet point.
- For self starting in thin metal or resin-filled plywood.
- A countersunk head with a rounded top surface and a cone-shaped bearing surface.
- Preferred over a flat head in conical applications, or when a more decorative finished look is desired.
- The countersunk surface nests into mating countersunk application sites.
- Oval head, phillips drive
- Screw diameter 12
- Screw length 1-1/4 inches
$0.3355
SHEET METAL SCREW HEX WASH HD #12 X 1/2"
- A thread forming tapping screw with spaced threads and a gimlet point.
- For self starting in thin metal or resin-filled plywood.
- Has an indented top surface, six flat sides with a flat washer which projects beyond the sides and provides a flat bearing surface.
- The washer and head are formed together as one piece. (Hex washer slotted head)
- Increased bearing area reduces likelihood of crushing mating surfaces.
- Zinc plated steel.
- Screw diameter 12
- Screw length 1/2 inch
$0.246
SHEET METAL SCREW PHIL PAN HD #12 X 1/2"
- A thread forming tapping screw with spaced threads and a gimlet point.
- For self starting in thin metal or resin-filled plywood.
- Phillips Pan Head
- For general applications.
- Can be substituted in most applications for round, truss or binding screws.
- Steel zinc plated.
- Diameter: 12
- Length: 1/2"
$0.2676
HEX CAP SCREW BOLT UNC ZINC 1/2"-13 X 1-3/4", GR 5
- Made from medium carbon steel.
- Heat treated.
- Tensile strength: 120,000 psi. minimum.
- Zinc plated.
- Unified screw threads :UNC.
- Diameter: 1/2"-13.
- Length: 1-3/4".
$1.3148
HEX CAP SCREW BOLT UNC ZINC 1/2"-13 X 1-3/4", GR 8
- Made from medium carbon alloy steel.
- Heat treated.
- Tensile strength: 150,000 psi. minimum.
- Yellow zinc plated.
- Unified screw threads :UNC.
- Diameter: 1/2"-13.
- Length: 1-3/4".
$1.6777