Retaining Rings
E-CLIP, RETAINING 3/8" SHAFT
EC38
- Stamped clips for deep grooves with three prongs that yield high thrust load capacity.
- Designed for radial installation into machined grooves on shafts of varying diameter.
- E clips require a deeper groove, but provide exceptional thrust loadings when compared to fasteners of the same size and weight.
- Can be safely used in a temperature range of -100 to 500°s F.
- Carbon steel material, heat treated.
- For shaft diameter of 3/8".
$11.50
$0.46
$0.46
E-CLIP, RETAINING 1/2" SHAFT
EC50
- Stamped clips for deep grooves with three prongs that yield high thrust load capacity.
- Designed for radial installation into machined grooves on shafts of varying diameter.
- E clips require a deeper groove, but provide exceptional thrust loadings when compared to fasteners of the same size and weight.
- Can be safely used in a temperature range of -100 to 500°s F.
- Carbon steel material, heat treated.
- For shaft diameter of 1/2".
$7.50
$0.30
$0.30
E-CLIP, RETAINING 7/8" SHAFT
EC78
- Stamped clips for deep grooves with three prongs that yield high thrust load capacity.
- Designed for radial installation into machined grooves on shafts of varying diameter.
- E clips require a deeper groove, but provide exceptional thrust loadings when compared to fasteners of the same size and weight.
- Can be safely used in a temperature range of -100 to 500°s F.
- Carbon steel material, heat treated.
- For shaft diameter of 7/8".
$15.22
$0.6088
$0.6088
E-CLIP, RETAINING 5/8" SHAFT
EC58
- Stamped clips for deep grooves with three prongs that yield high thrust load capacity.
- Designed for radial installation into machined grooves on shafts of varying diameter.
- E clips require a deeper groove, but provide exceptional thrust loadings when compared to fasteners of the same size and weight.
- Can be safely used in a temperature range of -100 to 500°s F.
- Carbon steel material, heat treated.
- For shaft diameter of 5/8".
$9.98
$0.3993
$0.3993
E-CLIP, RETAINING 7/32" SHAFT
EC732
- Stamped clips for deep grooves with three prongs that yield high thrust load capacity.
- Designed for radial installation into machined grooves on shafts of varying diameter.
- E clips require a deeper groove, but provide exceptional thrust loadings when compared to fasteners of the same size and weight.
- Can be safely used in a temperature range of -100 to 500°s F.
- Carbon steel material, heat treated.
- For shaft diameter of 7/32".
$8.91
$0.3564
$0.3564
E-CLIP, RETAINING 7/16" SHAFT
EC76
- Stamped clips for deep grooves with three prongs that yield high thrust load capacity.
- Designed for radial installation into machined grooves on shafts of varying diameter.
- E clips require a deeper groove, but provide exceptional thrust loadings when compared to fasteners of the same size and weight.
- Can be safely used in a temperature range of -100 to 500°s F.
- Carbon steel material, heat treated.
- For shaft diameter of 7/16".
$6.33
$0.2532
$0.2532
RETAINING/SNAP RING EXTERNAL, 1"
ERR1
- A ring-shaped stamping with one opening on the circumference.
- The two ends at the opening are called lugs and flare out slightly allowing for easier installation onto shaft.
- Installed axially on to a shaft.
- Allows for complete contact and tightness in a groove.
- Can be safely used in a temperature range of -100 to 500°s F.
- Carbon steel material, heat treated.
- For shaft diameter of 1".
$33.02
$1.3209
$1.3209
RETAINING/SNAP RING EXTERNAL, 11/16"
ERR1116
- A ring-shaped stamping with one opening on the circumference.
- The two ends at the opening are called lugs and flare out slightly allowing for easier installation onto shaft.
- Installed axially on to a shaft.
- Allows for complete contact and tightness in a groove.
- Can be safely used in a temperature range of -100 to 500°s F.
- Carbon steel material, heat treated.
- For shaft diameter of 11/16".
$14.68
$0.5872
$0.5872
RETAINING/SNAP RING EXTERNAL, 1/4"
ERR14
- A ring-shaped stamping with one opening on the circumference.
- The two ends at the opening are called lugs and flare out slightly allowing for easier installation onto shaft.
- Installed axially on to a shaft.
- Allows for complete contact and tightness in a groove.
- Can be safely used in a temperature range of -100 to 500°s F.
- Carbon steel material, heat treated.
- For shaft diameter of 1/4".
$10.40
$0.4158
$0.4158
RETAINING/SNAP RING EXTERNAL, 13/16"
ERR1316
- A ring-shaped stamping with one opening on the circumference.
- The two ends at the opening are called lugs and flare out slightly allowing for easier installation onto shaft.
- Installed axially on to a shaft.
- Allows for complete contact and tightness in a groove.
- Can be safely used in a temperature range of -100 to 500°s F.
- Carbon steel material, heat treated.
- For shaft diameter of 13/16".
$10.56
$0.4224
$0.4224
RETAINING/SNAP RING EXTERNAL, 3/8"
ERR38
- A ring-shaped stamping with one opening on the circumference.
- The two ends at the opening are called lugs and flare out slightly allowing for easier installation onto shaft.
- Installed axially on to a shaft.
- Allows for complete contact and tightness in a groove.
- Can be safely used in a temperature range of -100 to 500°s F.
- Carbon steel material, heat treated.
- For shaft diameter of 3/8".
$10.24
$0.4096
$0.4096
RETAINING/SNAP RING EXTERNAL, 3/4"
ERR34
- A ring-shaped stamping with one opening on the circumference.
- The two ends at the opening are called lugs and flare out slightly allowing for easier installation onto shaft.
- Installed axially on to a shaft.
- Allows for complete contact and tightness in a groove.
- Can be safely used in a temperature range of -100 to 500°s F.
- Carbon steel material, heat treated.
- For shaft diameter of 3/4".
$10.51
$0.4202
$0.4202
RETAINING/SNAP RING EXTERNAL, 1/2"
ERR50
- A ring-shaped stamping with one opening on the circumference.
- The two ends at the opening are called lugs and flare out slightly allowing for easier installation onto shaft.
- Installed axially on to a shaft.
- Allows for complete contact and tightness in a groove.
- Can be safely used in a temperature range of -100 to 500°s F.
- Carbon steel material, heat treated.
- For shaft diameter of 1/2".
$10.10
$0.404
$0.404
RETAINING/SNAP RING EXTERNAL, 5/16"
ERR56
- A ring-shaped stamping with one opening on the circumference.
- The two ends at the opening are called lugs and flare out slightly allowing for easier installation onto shaft.
- Installed axially on to a shaft.
- Allows for complete contact and tightness in a groove.
- Can be safely used in a temperature range of -100 to 500°s F.
- Carbon steel material, heat treated.
- For shaft diameter of 5/16".
$10.30
$0.412
$0.412
RETAINING/SNAP RING EXTERNAL, 5/8"
ERR58
- A ring-shaped stamping with one opening on the circumference.
- The two ends at the opening are called lugs and flare out slightly allowing for easier installation onto shaft.
- Installed axially on to a shaft.
- Allows for complete contact and tightness in a groove.
- Can be safely used in a temperature range of -100 to 500°s F.
- Carbon steel material, heat treated.
- For shaft diameter of 5/8".
$17.02
$0.6808
$0.6808
RETAINING/SNAP RING EXTERNAL, 7/16"
ERR76
- A ring-shaped stamping with one opening on the circumference.
- The two ends at the opening are called lugs and flare out slightly allowing for easier installation onto shaft.
- Installed axially on to a shaft.
- Allows for complete contact and tightness in a groove.
- Can be safely used in a temperature range of -100 to 500°s F.
- Carbon steel material, heat treated.
- For shaft diameter of 7/16".
$11.70
$0.468
$0.468
RETAINING/SNAP RING EXTERNAL, 9/16"
ERR96
- A ring-shaped stamping with one opening on the circumference.
- The two ends at the opening are called lugs and flare out slightly allowing for easier installation onto shaft.
- Installed axially on to a shaft.
- Allows for complete contact and tightness in a groove.
- Can be safely used in a temperature range of -100 to 500°s F.
- Carbon steel material, heat treated.
- For shaft diameter of 9/16".
$10.56
$0.4224
$0.4224
RETAINING/SNAP RING EXTERNAL, 7/8"
ERR78
- A ring-shaped stamping with one opening on the circumference.
- The two ends at the opening are called lugs and flare out slightly allowing for easier installation onto shaft.
- Installed axially on to a shaft.
- Allows for complete contact and tightness in a groove.
- Can be safely used in a temperature range of -100 to 500°s F.
- Carbon steel material, heat treated.
- For shaft diameter of 7/8".
$22.17
$0.8869
$0.8869
